Official Coffee Lake Refresh Thread/BIOS for ALL Clevo Laptops - RTX CARDS NOW SUPPORTED

Official no. And i highly doubt you can get a newer CPU in your laptop since the socket is not highly supported with current CPUs

your best bet is to gather some money and get a more recent laptop from P7xxx series (which support socketed CPU's and MXM GPUs)

 

@unisev can put in an i7-4930/i7-4940mx (Haswell Mobile Extreme).

 

I'm currently running the P7xxDMx_RTX bios on a P775DM3 with an I7-7700K and a RTX 2070. I pushed the bios update primarily for the RTX support, but now my CPU is constantly Current/EDP throttling even at idle. Package TDP stays below 30 watt no matter and under load the cpu drops to around 2.6 GHz. Are there bios options I can change to get my cpu back where it was? I'm planning on putting in a newer processor once i find the right deal, but would like this to work first. If anyone has any ideas please let me know.

 

In the overclocking sub menu of the bios there should be a current limit, what is that set to?

 

The VR current limit was set to 1023, i just raised it to 2500 and no change.

 

Can you post a screenshot of your FIVR window and limits window open in throttlestop?

 

And power limit1 and power limit2? Set to 250000 both

 

Here's a screenshot of FIVR

 

Power limit 1 and 2 were set to 511855

 

In the FIVR window, can you try increasing IccMax?

 

Yes, raised it to 255.75A, still being edp/current limited. I'm willing to try anything at this point i even put a substantial under volt (-0.250) which seems to have done something because my benchmarks are looking better, but still nowhere near where a stock 17-7700k should be.

 

Can you try clearing the CMOS and leave bios settings stock for a test.

If that's no good, we might need to get photos of the all CPU & power related tabs in the bios to compare.
I can only compare with the 8600 running in my P870DM but I guess that's better than nothing.

 

Anyone experiencing same issue as described here?

 

I've reset the bios multiple times, even using FN + D, but no luck. Here's the pictures of my bios options: https://imgur.com/a/wwJngnj I know it's a lot but most of them have headers on the pictures to match up what's in the bios.

 

Your photos seem to match up with my bios values on my P870DM, except for one setting that I don't know much about.

It's under the CPU VR Settings, "TDC Enable".

Yours is enabled in all screenshots and mine is disabled on those same tabs.

You can also try changing PSYS Pmax power (maybe try a value of 2400).
Then go to system agent VR settings and set the VR Current limit to 2400.

And lastly, have you tried testing without any undervolt applied?

 

Its posible to run USB C port on P775DM3G RTX bios ? Now i have I7 8700K and RTX 2080 and i can't run this USB C

 

Hi there . . .

found a FanControl Solution for Clevo but also miss again a BaidoAccount !

If maybe someman can acess the Files and find them well fell be free to Share here . . . Pleaseee

https://pan.baidu.com/s/13Ywv1XZB00zFXjLSOXGM4A#list/path=/
https://translate.google.com/translate?hl=de&sl=zh-CN&u=https://tieba.baidu.com/p/5971634018?pid=123147225384&see_lz=1&prev=search&pto=aue
https://tieba.baidu.com/p/5971634018?pid=123147225384&see_lz=1

Ah and to do not Forget there after Years searching . . . P751DM self unlocked StockBios works . . . you know non K CPU lock ;-(

Use this Tool Only by Using Manual set Values the Automate Mode seams to be Bug by Disable Fans Complete
http://forum.notebookreview.com/threads/rlecviewer-custom-clevo-fan-control.818858/

Greetings !

 

Is buged try with 1.07.24 version of bios

 

Is normal this bios is build to 9th and 8th gen the support of the 6 ; 7 gen is only to boot but the performance is very bad... put inside a 9700k (for exemple) and all be fine

 

Now i have
1.07.24

 

And you usb works ?

 

Yes all 3.0 USB Work. 2x USB-C no. On older bios all USB C works and USB 3.0

 

Go another version !!!

 

1.07.24 only support RTX 2080 on P775DM3G now I have RTX 2080

 

Ohhh ok honestly i dont know beacause with 128Gb ram usb c is disable

 

Ahhh ok I have 32GB 3200MHz and its optimal to me

 

you don't have the 128Gb version of the bios ???

 

No

 

Dsanke buged version and 0 patch.....

 

What a shame. Maybe he make new bios.

 

P751DM1 is mainly dead without a proper BIOS with latest CPU and GPU support. The issues with audio drivers and now with the keyboard backlit is getting annoying, also shutting down also is not working properly.

 

Right P751DM1 is annoying . . .im Run with Skylake and Maxwell2 but triggerd by sometimes Integrate newest CpuMicroCode and IntelMeFirmware into latest StockBios makes Somtimes Chilling over Annoy . . . and maybe RLECViewer does a part for that ! ! ?

 

Does it work like this?

I use @dsanke BIOS with Kaby and Pascal. When I tried to install some drivers for keyboard backlit it broke the lightbar which no longer appears in the hotkey app.

This RLECviewer? : https://github.com/zuyan9/RLECViewer

 

Im using this RLECViewer v2.4 http://forum.notebookreview.com/threads/rlecviewer-custom-clevo-fan-control.818858/ please read from first @ last entryfor Secure Useage !
Downloadlink Installer: https://github.com/duguzuyang/RLECViewer/raw/master/Install/Product/RLECViewer.exe !
Running now for a week with Monitoring Fanspeeds per MSI AfterBurner and there are maybe Scary behavior on first look but for me it´s not Critical

P751DM1 and other CPU as Skylake is a mess Only with begin of P7xxDM Models with Native Kabylake support is the option to use NextGeneration CPU without much trouble . . . Ds@nke self went to P751DM2.
Your trouble with audio drivers and keyboard backlit also shutting down is Normal on P751DM1 with Kabylake and what i read from Modders to complicate to be Fixed.

Also with Skylake CPU and Ds@nke Mod Bios there trouble with audio drivers and keyboard backlit also shutting down .

 

Audio drivers and backlight definitely an issue with my p870dm + i5-8600.

The other issue is when on battery power, I get random BSOD (no matter even if I increase voltages in bios and run stock clocks for everything).
Not a big deal because this thing is always on a desk connected to power.

Lastly, when gaming with the 980m, the machine turns off and power adapter light goes off. Like it's hitting overcurrent Protection.

I've messed with all the cpu current limit settings in the bios with the same result.

The 980m doesn't have this behaviour when running in my p375sm.

Unsure whether those issues will be solved when I eventually upgrade the cpu, ram and GPU.

This is Sager branded, no idea which reseller was the original seller and whether Prema bios would be an option.

For now, this machine is just being used for my studies and not any gaming.

 

Hi all,
Finally I have managed to upgrade my 751dm2 with 1.07.24 RTX dsanke bios! I have bough an intel QQBZ cpu, which is almost an i9 9900 with lower clocks (4,4-4,2). The issue what I have, that under stress the cpu is stuck at 2,6Ghz. The only bench I have managed to keep the original clock (4,2@all core) is the cpu-z bench. With that the cpu used 100W+, so it seemed fine. With CB15 the scores were also poor, all clock 2,6ghz. P95 same What could be the issue? Thx!

 

I am not sure where from the backlit config comes from, it is controlled by second EC but it's also connected to main EC and to PCH as well. It worked fine for me until drivers broke it, and I am not sure how to fix it now.
Apart of that, because it's a different audio codec ALC892 in 750dm vs ALC898 in 750DM2 maybe this is one reason with drivers. Replacing the 892 codec with 898 is not very straight, and not sure it will work, there a re a few different pinouts.

Maybe the charger is dying.

Could be again main EC firmware issue like in 750DM.

Without prema mod... it's unusable.

 

Hi everybody (i'm a newbe and my english is bad, sorry for that).
I think i bricked my laptop (P870KM1G), i don't know how. all works fine until yesterday during a clean installation of win10, after intelMe drivers installation (well done), no problems, but after that i had to pick the phone(for 30min). When i was back it was in sleeping mode (normal), but it wasn't start until that. when I start it (start button) the laptop turn on (without any screen during 2s) turned off immediately.
If someone knows what is the problem exactly.
My cfg at last before death: P870KM1-G Dsanke Bios, I9 9900KF CPU, GTX 1080 GPU x2 in SLI with G-Sync activated (UHD panel), audio working fine with SoundBlaster connect 360 app no issues, the only thing i didn't have was the thunderbolt cause i've flashed the thunderbolt controller (winbond 25Q80DV...) with bios firmware because i though that was it, with no backup, my missed up.

Thanks for all

 

Could just be unlucky and have a component failure.

Try starting the machine with just 1 GPU installed and 1 stick of ram.

 

Was on same Isue and try remember me right . . . had Ds@nke bi0s but Played with the Intel-Me-Firmware by my self updatet the bi0s had
triggered the Isue . . . by plug out or in the Accu after that the DeskTop go on again . . . then was a other Isue while PSU was pluged in and did a restart of Windows the PSU shuts down and only after disconect PSU from howl Energy it was usable to Power on the DeskTop . . . this behavior was still Present with Stock bi0s so i have a Half Functional PSU . . . to Run the DeskTop it was something to do with Accu and disconecting the PSU .

So the PSU works for PowerOn the DeskTop but do a restart lets ShutOff the PSU also with Accu Pluged in . . . maybe dont Install IntelMeFirmware directly and try to use only the drivers that windows do Install if you can awake your P870KM1G again . . . Lucky Luck for th@t !


Could just be unlucky and have a component failure.

Try starting the machine with just 1 GPU installed and 1 stick of ram.

 

thanks for your answers.

Did try that but no difference.

Didn't check the PSU (2x 330W w/ adapter), i'll do it.

 

@joluke Hi, I noticed you said you got your USB-C ports all working by downgrading the BIOS version to 1.07.24. I'm using a P870km with BIOS 1.07.15 installed and neither USB-C ports work. I wonder what was your BIOS version before the downgrading? Was it v.25? Are there any downsides that you notice through downgrading? The folder "Clevo ALL 9th (16-05-2019)" you uploaded contains all the v.24 BIOS, right? Thanks a lot!

Does anyone else have USB-C/Thunderbolt issues? Please share your solutions/thoughts. Appreciate it.

 

I had this one before downgrading to 1.07.24 in my P775DM3-G:

https://prnt.sc/tsihdu

Its a modified BIOS from P775TM1-G adapted to my P775DM3-G

Please keep in mind these are different generation of laptops and BIOS features being modified can work in some and not work in others!!!

 

Thanks for your reply. I just realized that my BIOS is already on the fairly early May-2019 version and cannot be downgraded any more. The BIOS I have is P870KM_RTX.rom v1.07.15. I might give the non-RTX v1.05.11 a try to see if USB-C ports work. Meanwhile, I wonder where did you find the newer version of BIOS, like your 1.07.26? The BIOS in the OP seems to be still on the May-2019 version, and I have gone through dozens of pages and have yet to find a newer version of BIOS for my P870km.

 

USB-C issue.
No USB 3.1 Host controller in Device Manager. Laptop: P870km-g, BIOS: P870KM_RTX.rom, v1.07.15.
I notice that if my USB-C drive is plugged in during booting up, the USB-C drive will be recognized by the laptop just fine and USB 3.1 Host controller shows up in device manager. But once it is removed, it won't be recognized after plugging back in, unless I do another restart with the drive plugged in. I thought it had something to do with the BIOS. But now it feels like some windows driver problem with the new win10 2004 version.
@KKthebeast I saw the same issue has been posted by you on P139. I wonder if you had this issue before upgrading to win10 2004 version? Have you resolved this issue now?

 

Why not just downgrade (which is actually an upgrade) to see if getting rid of W10 2004 cancer fixes it? Then you would have a very definitive answer that would benefit you and others. If it does we can add your problem to massive list of unacceptable atrocities associated with W10 1903, 1909 and 2004. You've nothing to lose and everything to gain. You can make an image of your current Windoze 2004 in about 15 minutes with Macrium Reflect free edition and if upgrading to an older version of W10 doesn't fix it you can restore the image in about 15 minutes.

Windows 10 Enterprise LTSC 2019 Download

 

I would if I could. I upgraded to win10 2004 version months ago and didn't notice any issue, so I just deleted the windows.old folder using the Disk Cleanup. Now I couldn't roll back to previous versions of windows. Thank you for your suggestion though.

 

Good Day Everyone,
I'm looking to upgrade my P870TM_TM1 laptop from i7-8700K to a i9-9900K. My bois is the default Bios my laptop came with ( AMI 1.05.02 dated 10/13/2017 ) What would i have to do to upgrade the CPU? I already maxed out the ram at 64gb and installed 970evo nvme drive. Is it just a plug and play or do i have to install a new bios? Any help would greatly be appreciated.

 

Sure you can. No need for the Windows roll-back feature. You should never be reliant on that capability anyhow because the process is inherently unreliable. It only takes a few minutes to create a Macrium Reflect image and do a clean install of an older version of Windows? If it doesn't work, it only takes a few minutes to restore the image. If it does work, then your problem is solved.

 

Mr Fox,
Could you help what the issue could be?

Finally I have managed to upgrade my 751dm2 with 1.07.24 RTX dsanke bios! I have bough an intel QQBZ cpu, which is almost an i9 9900 with lower clocks (4,4-4,2). The issue what I have, that under stress the cpu is stuck at 2,6Ghz. The only bench I have managed to keep the original clock (4,2@all core) is the cpu-z bench. With that the cpu used 100W+, so it seemed fine. With CB15 the scores were also poor, all clock 2,6ghz. P95 same What could be the issue? Thx!