The Notebook Review forums were hosted by TechTarget, who shut down them down on January 31, 2022. This static read-only archive was pulled by NBR forum users between January 20 and January 31, 2022, in an effort to make sure that the valuable technical information that had been posted on the forums is preserved. For current discussions, many NBR forum users moved over to NotebookTalk.net after the shutdown.

M4600 + OCZ Vertex 3 MaxIops

Discussion in 'Dell Latitude, Vostro, and Precision' started by dtsymbal, Jun 24, 2012.

Thread Status:
Not open for further replies.
  1. dtsymbal

    dtsymbal Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    Gurus,

    i need your help with next issue. Just receive my new m4600. Put Vertex3 MaxIOPS 120Gb as a primary disk. Win7 x64 was deployed from corporate image with default parameters - not much you can select during deployment. After that all latest drivers\updates were installed.

    Intel RST shown that my SSD working on 3Gb\s transfer rate.
    also my mSATA OCZ Nocti 120Gb connected to intenal slot, speed fell almost twice comparing to previous system (m4500)

    Could you please share your ideas how i can push my system to use SATA III. Right not it shows SATA 2 only :(
     
    dtsymbal, Jun 24, 2012
    #1
  2. dtsymbal

    dtsymbal Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    No ideas at all ?
     
    dtsymbal, Jun 25, 2012
    #2
  3. foal

    foal Newbie

    Reputations:
    0
    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    5
    I have the same situation with RunCore V Sata III. Transfer rate is 3Gb. Have some body some ideas?
     
    foal, Jun 25, 2012
    #3
  4. dtsymbal

    dtsymbal Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    guys, no ideas?
     
    dtsymbal, Jun 27, 2012
    #4
  5. Tsunade_Hime

    Tsunade_Hime such bacon. wow

    Reputations:
    5,413
    Messages:
    10,711
    Likes Received:
    1,204
    Trophy Points:
    581
    Did you try updating your chipset drivers? Also are you talking about internal 2.5" slot running @ SATA 2 or the mSATA, I'm not sure M4600 supports SATA 3 on mSATA slot.
     
    Tsunade_Hime, Jun 27, 2012
    #5
  6. hf2046

    hf2046 Notebook Guru

    Reputations:
    18
    Messages:
    55
    Likes Received:
    0
    Trophy Points:
    15
    In your BIOS -> System Configuration -> SATA Operation is the AHCI option selected?
     
    hf2046, Jun 29, 2012
    #6
  7. dtsymbal

    dtsymbal Newbie

    Reputations:
    0
    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    5
    Main issue with 2.5 internal drive.
    mSATA OCZ Nocti card also working slowly.

    Latest drivers from Intel support page were downloaded.

    BIOS in ACHI mode (RAID mode also tested - same issue)
     
    dtsymbal, Jul 1, 2012
    #7
  8. Atom Ant

    Atom Ant Hello, here I go again

    Reputations:
    1,340
    Messages:
    1,497
    Likes Received:
    272
    Trophy Points:
    101
    It is because OCZ drives are sucks. I also had half speed issues with Agility 3 in Dell and nothing could solve my problem other than replace the drive with Samsung Series 830 128GB.
     
    Atom Ant, Jul 1, 2012
    #8
Thread Status:
Not open for further replies.

Share This Page